Electric Jet Cleaner High Pressure Washer Pump Shaft 150 Bar 2200PSI 15L

HY Brand VFD &SPINDLE MOTOR. Electric Pottery Wheel Machine For Ceramic Work Clay Art Craft DIY 350W 25CM. 3500A PRO Vehicle Panel Spot Puller Dent Spotter Multispot Bonnet Door Repair. Pipe Crimping Tool Pex Pipe Crimper Pressing tools w/ TH Dies 16, 20, 26, 32. Portable Mini Rosin Extracing Press 2"x3" Dual Heat Aluminum Plates Machine 220V. 220V Gem Faceting Machine Jewelry Polisher Jade Flat Grinder 150mm Disc. Aluminum Demolition Hammer Concrete Breaker Jack hammer Drill Electric 1500W. Electric Jet Cleaner High Pressure Washer Pump Shaft 150 Bar 2200PSI 15L. A quality high pressure plunger type pump with brass head to. Pressure washers, steam cleaners and jet washers etc. Product Name: Pressure Washer Pump.

Apply to: Cleaning the car, cleaning the floor (for washing machine). Inlet - 1/2 BSP Female. Outlet - 3/8 BSP Female.

This pump is a high-pressure, high-speed light and small three-cylinder plunger pump. The pump has a high speed and can be directly connected to a 4-pole motor without the need for a deceleration device. The pump is compact, small in size and light in weight.

The device is mainly used for conveying normal temperature and clear water. The device is suitable for high-pressure cleaning machinery, agriculture and forestry plant protection machinery, water-saving irrigation machinery, pressure calibration equipment, and the like. The power is converted into the reciprocating motion of the plunger through the crank linkage mechanism.

When the plunger is retracted, the inlet valve is opened and the outlet valve is closed due to the vacuum suction, and the water is sucked into the cylinder; when the plunger advances, As the water pressure in the pump rises, the inlet valve is closed, the outlet valve is opened, and the high pressure water is discharged from the outlet valve through the high pressure pipe. The establishment of the pump pressure depends on the resistance of the pump outlet, while the resistance is high and the pressure is high, otherwise the pressure is low. Generally, the unloading valve has been adjusted to the rated pressure, no need to adjust.

If it needs to be adjusted again, the gun should be fired first. After the gun is fired, the pressure regulating handwheel of the unloading valve is rotated to make the pressure reach the predetermined value.

The pressure regulating valve is mainly composed of a pressure regulating cover, a pressure regulating spring, a valve stem and a ball valve seat, a check valve seat and a check valve core. The model of this pump with pressure regulating valve is 3/8 external water pressure regulating valve. The functions of the pressure regulating valve include: 1 can be adjusted. 2 When the spray gun is turned on, the pressure immediately reaches the set value, and when the spray gun is turned off, the pump pressure immediately drops below 1 MPa. If the unloading valve is not installed, the pressure will be higher when the gun is turned off than when it is sprayed, and it consumes more power than when it is used.

Therefore, the use of the unloading valve is an effective method for energy saving. Under normal circumstances, it can save about 30%.

To ensure safe use of the pump, it is strictly forbidden to operate the pump without reading the instruction manual to prevent accidents and unnecessary losses. If the motor is used as the power, the grounding of the machine must be safe and reliable.

The power supply end must be equipped with a leakage protection switch or a safety protection device. (CD 15W-40) oil should be added to the crankcase. The oil level should be half of the oil mark. It is strictly prohibited to operate before the lubrication is added. When stopping the use, the power of the pump should be cut off first, then the water source should be turned off. The pump outlet pressure should be matched properly. When using, the pump pressure must not exceed the maximum working pressure. In order to prevent impurities from being sucked into the inlet pipe, a filter with sufficient filtration area must be installed, and the mesh size is required to be no less than 40 mesh/inch. Our company is an emerging professional Cross-Border Electronic company. So far we have finished the assets re-organization and obtained wholesale financing.

We guarantee every product is of high quality and durable utility compared to other factories becayse we choose the best-buys goods. We are really appreciated if you would like to give us your valuable positive comment(s) after you receive our products, which is a huge encouragement for us to make our products and service better and better. Hope you will love our items. Any questions will be answered promptly, so please feel free to let me know your concern.

We now have warehouses in Germany. Please do check everything carefully when receiving the package. Failure to do so might result in damage to your own rights and interests. The item "Electric Jet Cleaner High Pressure Washer Pump Shaft 150 Bar 2200PSI 15L" is in sale since Tuesday, May 28, 2019. This item is in the category "Business, Office & Industrial\Cleaning & Janitorial Supplies\Pressure Washers, Parts & Accessories\Electric Pressure Washers". The seller is "nice-shop2" and is located in Prague. This item can be shipped worldwide.

Brand: Taishi
Country/Region of Manufacture: China
Flow: 15L/min
Gross Weight: 7.2kg
Horsepower: 5.5hp
MPN: UK2019052826
Package Size: 27*24*23(cm)
Pressure Rating: 150Bar/2200psi
Roating Speed: 1450rpm